Stone Surface Solutions

Onsite Stone Cutting & Drilling · Auckland

Hob Cutting & Stone Alterations

Professional onsite stone cutting and drilling to accommodate replacement appliances, upgraded cooktops and new fixtures.

Servicing Warkworth, Omaha, Matakana and Snells Beach, as well as the wider Auckland region.

We use an H-Class vacuum for effective dust capture.

High-level dust capture at the source helps create a cleaner, more controlled onsite working environment. No system guarantees a completely dust-free environment.

Pricing

Straightforward Onsite Pricing

Hob & Cooktop Cutting

  • Per cut$150

Hole Drilling

  • Per hole$125

$250 minimum per visit - not an extra fee.

It covers the cost of attending the site. Where the calculated price for the requested work is below the minimum, the minimum charge applies instead.

For multiple cuts or holes, the price is calculated using the applicable per-cut or per-hole rate, subject to the minimum charge and any separately agreed additional work.

How Hob Cutting Is Priced

Hob Cut-Out Alteration: A Pricing Example

Here's an example of how we calculate the cost of enlarging an existing hob cut-out to accommodate a new appliance.

Existing Cut-Out
550 mm480 mmTOP-DOWN VIEW
New Required Cut-Out
Existing openingNew openingMaterial removedRear edge unchanged123New width: 560 mmNew depth: 490 mmCut 1 - 5 mm removed from leftCut 2 - 5 mm removed from rightCut 3 - 10 mm removed from front

3 cuts × $150 = $450

In this example, 5 mm is removed from each side and 10 mm from the front. The rear edge stays unchanged, so three cuts are needed.

The example total already exceeds the minimum call-out, so no additional call-out fee is added.

This is an illustrative pricing example. Actual cutting requirements depend on the replacement appliance's installation specifications and the existing benchtop. The proposed alteration must be assessed for suitability before work begins.

Service One

Onsite Hob & Cooktop Cutting

Stone Surface Solutions provides onsite hob cutting and stone alterations to help modify suitable existing openings and create new holes where required.

Have you upgraded your cooktop, replaced an appliance or purchased a new fixture that doesn't fit your existing stone benchtop?

Replacing an existing cooktop can sometimes require modifications to the opening in your stone benchtop.

Different cooktop models can have different installation requirements, even when their external dimensions appear similar. An existing cut-out may need to be widened, lengthened or otherwise modified to accommodate the replacement appliance.

Stone Surface Solutions provides onsite hob and cooktop cut-out alterations for suitable stone benchtops, helping customers accommodate new or upgraded appliances without unnecessarily removing the existing benchtop.

Whether your new hob needs a slightly larger cut-out or you need an additional hole drilled for a tap or fixture, we can assess the requirements and provide clear pricing before work begins.

For granite benchtop cutting and engineered quartz benchtop alterations in Auckland, we assess the material and proposed cooktop cut-out modification before confirming suitability.

Common reasons customers need this service

  • A replacement hob requires a wider opening.
  • A new cooktop requires additional clearance.
  • An upgraded appliance has different cut-out dimensions.
  • An existing opening needs to be modified to match the manufacturer's installation specifications.

All alterations are subject to the stone type, benchtop thickness, structural clearances and the feasibility of the proposed modification.

Service Two

Onsite Stone Benchtop Hole Drilling

Need an additional hole for a tap, soap dispenser or another suitable fixture?

Stone Surface Solutions provides onsite hole drilling for suitable stone benchtops. This service is ideal when replacing fixtures, upgrading fittings or modifying an existing kitchen to accommodate new hardware.

We assess the proposed hole location, diameter, surrounding stone and access requirements before confirming the work.

Suitability depends on the material, stone thickness, edge distances, existing openings, reinforcement and the risk of cracking. We confirm feasibility before accepting the work.

Dust Control & Site Requirements

Professional Onsite Dust Extraction

Onsite stone cutting and drilling require appropriate equipment and dust management.

Stone Surface Solutions uses an industrial H-class dust extractor to capture hazardous fine dust at the source and help control dust generated during the work.

A suitable power supply must be available at the property to operate the cutting equipment and dust extraction system.

H-class dust extraction helps control hazardous dust but does not guarantee a completely dust-free environment. Additional controls and site preparation may be necessary.

The Process

How Our Onsite Alteration Service Works

01

Send Us the Details

Request a quote using the alteration enquiry form below.

02

Confirm the Requirements

We assess the proposed alteration, likely number of cuts or holes, site access and suitability. We then confirm the scope and price before proceeding.

03

Complete the Alteration Onsite

Once approved, the work is completed onsite using suitable stone-working equipment and H-class dust extraction, subject to the agreed scope and site conditions.

Request Your Quote

Enquiry

Request a quote for your alteration

Hob Cutting & Stone Alterations - Quote Request

Questions

Frequently Asked Questions

Can you enlarge an existing hob cut-out?

Yes. We can assess whether an existing stone cut-out can be modified to accommodate a replacement cooktop. Suitability depends on the stone, clearances, appliance specifications and proposed alteration.

Do I need to remove my benchtop?

This service is designed for suitable alterations to installed benchtops, allowing many modifications to be carried out onsite. Suitability depends on the particular job.

Can you alter granite and engineered stone?

We assess the stone type and proposed alteration before confirming the work. Different materials have different working requirements, so not every modification is suitable.

Do you need power onsite?

Yes. A suitable power supply is required for the cutting equipment and H-class dust extraction.

Will there be dust?

Dust extraction is used to capture fine dust at the source and help control dust during the work. However, no system can guarantee a completely dust-free environment.

Can you drill a hole anywhere in the benchtop?

Not necessarily. The proposed position must be assessed for stone thickness, edge distances, surrounding openings, reinforcement and cracking risk before drilling.

New hob? New tap? We'll make the stone fit.

Request your alteration quote - we'll confirm the scope and price before any work begins.

Related services: stone benchtop repairs, granite chip repairs, stone sealing and marble restoration.